Shop Talk Live - Fine Woodworking

Question 1:

From Tony:

We hear so much talk about  Lie Nielsen, Veritas, and Stanley hand planes but, I have a Millers Falls No. 8 that i picked up from an Antique store, that works really well. I don't think I’ve ever heard the Millers Falls Name be mentioned on the Podcast, so I am wondering if they’re any good? They seem to have been in contention with Stanley and they are American made from New England no less, since 1868!

Question 2:

From Matt:

I have been wanting to do a project using drawbore mortise and tenon joints. Is it a bad idea to attempt this type of joint in a softer woods like cherry or walnut, rather than oak.

Segment: Smooth Move

  • Mike - Forgetting that someone commissioned something from him, not those he looks up to
  • Barry - Making a mistake on a piece, remaking the piece, then accidentally using the mistake on the final piece
  • Ben - Trying to get away with not making a proper sled and accidentally dropping a piece on the tablesaw blade

Question 3:

From Bob: Can someone explain the difference between a scrub plane and a smooth plane? They seem similar in size and construction.

Question 4:

From Phillip:

I am looking to build a dining room table to a friend of mine, and am wondering what type of wood would be best to use. I have narrowed it down to White Oak, Cherry, and Walnut. The friend that I am making this for is a military man, and so gets stationed at different bases around the country every few years. My main concern is the table warping or splitting due to the drastic location and environmental changes that he will come across. Obviously, being a dining room table it also must be sturdy and not be too prone to scratches, dings, etc. White Oak is very wear resistant, but has a medium-high shrinkage value. Cherry is pretty stable once dried, but is softer and may get more dings. Walnut seems to be the middle road, being harder and less susceptible to scratches than Cherry but less likely to shrink/warp than White Oak.

What type of wood would you suggest that is going to be resistant to scratches and dings, yet won't warp or split in drastic climate changes? 

Recommendations:

Barry - Dedicated Shop Shoes
Ben - Chris Thile's Thank You, New York"
Mike - Tom Waits' album Swordfish Trombones


Every two weeks, a team of Fine Woodworking staffers answers questions from readers on Shop Talk Live, Fine Woodworking‘s biweekly podcast. Send your woodworking questions to shoptalk@taunton.com for consideration in the regular broadcast! Our continued existence relies upon listener support. So if you enjoy the show, be sure to leave us a five-star rating and maybe even a nice comment on our iTunes page.

Direct download: shop-talk-live-episode-179.mp3
Category:general -- posted at: 10:58am EST

To enter to win Bob Van Dyke's sharpening box from issue #254:

  1. Leave a comment on this episode's show-notes page
  2. Head over to the Connecticut Valley School of Woodworking site and sign up for their email list

We’ll pick a winner December 21, 2018.

Question 1:

From Amy: I've been using a piece of vegetable tanned leather with green waxy honing compound as a strop. I start by rubbing compound onto the shiny side of the leather. However, when I go to strop my carving knives, the pressure from my blade compresses the compound and it flakes off. Is there something wrong with my compound, or am I doing something wrong?

Question 2:

From Matt: I have some 10-in. wide 8/4 African Mahogany that I have been resawing into thinner boards.  I start by jointing one face then one edge and then resawing, usually down the middle. There is a good amount of tension in the boards, so after resawing they have a decent twist.  Do I need to let the boards re-acclimate before I re-joint and plane them, or can I do that immediately? Also, would I be better off not jointing the face and resawing to a center-line rather than using the bandsaw fence. It seems like a waste of time getting that face flat just so I can use the bandsaw fence.

  All Time Favorite Technique

Bob: Fixing a mistake and perfectly matching both the face grain and end grain. 

Ben: Using a sawbench to support the ramps when moving machinery off the back of a pickup truck

Mike: Using a bird-mouth joint to create dividers

Question 3:

From Matt (in Australia): I see many of the worlds best woodworkers only apply glue to one mating surface of a joint not both as advocated by Hoadley. When is it acceptable to only apply glue to one surface of a mating joint?

Question 4:

From Anthony: Last couple years I’ve been on the hunt for an 8” jointer and just recently I was able to secure a CL purchase on a 12” jointer that I’m pretty excited about. It’s a Bridgewood 12” 5hp that I picked up a few hours away from a now retired door maker. As with most home woodworkers, my jointing experience has been on a six inch jointer. What are the potential areas of concern with a larger jointer? In general, with a jointer, what leads up to an accident? Is it simply being unaware of your hands and proper use?

Recommendations:

Ben - David Johnson's Instagram Page

Bob - His own Instagram page

Mike - Go buy a fresh bottle of glue


Every two weeks, a team of Fine Woodworking staffers answers questions from readers on Shop Talk Live, Fine Woodworking‘s biweekly podcast. Send your woodworking questions to shoptalk@taunton.com for consideration in the regular broadcast! Our continued existence relies upon listener support. So if you enjoy the show, be sure to leave us a five-star rating and maybe even a nice comment on our iTunes page.

Direct download: shop-talk-live-episode-178.mp3
Category:general -- posted at: 11:31am EST

1